Just How to Remove as well as Replace a Bath Tub.
Just How to Remove as well as Replace a Bath Tub.
Blog Article
Each person seems to have their own thinking involving Tools You Need to Install a New Bathtub .
Mounting a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is easily accessible, the task can move quickly; if you need to open a wall surface to remove the old bathtub and place the new bath tub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will certainly aid you install a brand-new bath tub in your restroom if you have actually currently purchased a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your devices and material list should comprise the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Before carrying on to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the spirit level reads level.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water supply and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait until the tub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in place between the tap and the sink. Protect the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former type should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with moisture and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can split fairly very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our section on How to Install a Bathtub. Thanks a ton for taking a few minutes to read our posting. Enjoyed reading our posting? Please share it. Let others locate it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Phone Report this page